M.a.p. sensor

JurScrx · Post by **JurScrx** » Thu Mar 20, 2008 1:58 pm

Well, I ask ya'll because I know you guys know what you're talking about. I have looked up in manuals,but I've had no luck. I'm glad somethings hooked up right..lol. Just need to figure out why the ecu light is staying on,and all that.

Waffles · Post by **Waffles** » Thu Mar 20, 2008 2:02 pm

JurScrx;104009 wrote:Well, I ask ya'll because I know you guys know what you're talking about. I have looked up in manuals,but I've had no luck. I'm glad somethings hooked up right..lol. Just need to figure out why the ecu light is staying on,and all that.

Try plugging the plug on the MAP into the TPS, and the TPS into the MAP.

rickles8099 · Post by **rickles8099** » Thu Mar 20, 2008 2:07 pm

JurScrx;104009 wrote:Well, I ask ya'll because I know you guys know what you're talking about. I have looked up in manuals,but I've had no luck. I'm glad somethings hooked up right..lol. Just need to figure out why the ecu light is staying on,and all that.

find out how many times the light on the ecu is blinking and we can tell you what the codes mean.

JurScrx · Post by **JurScrx** » Thu Mar 20, 2008 2:38 pm

btlfedgolf;104012 wrote:Try plugging the plug on the MAP into the TPS, and the TPS into the MAP.

It ran worse and died when i tried giving it gas

JurScrx · Post by **JurScrx** » Thu Mar 20, 2008 2:39 pm

rickles8099;104014 wrote:find out how many times the light on the ecu is blinking and we can tell you what the codes mean.

I could too,if the light was blinking. =(. I need this car.

Spork · Post by **Spork** » Thu Mar 20, 2008 2:49 pm

have you tried pulling the hazard fuse to reset the ecu since you have been messing with it? you should be doing that regularly when you are changing stuff around to try and fix this. if the light comes back on it should be accompanied by a code on the ecu...

JurScrx · Post by **JurScrx** » Thu Mar 20, 2008 3:11 pm

Spork;104025 wrote:have you tried pulling the hazard fuse to reset the ecu since you have been messing with it? you should be doing that regularly when you are changing stuff around to try and fix this. if the light comes back on it should be accompanied by a code on the ecu...

Yep,just tried reseting the ecu..light stays on,on the ecu itself. Car WILL NOT rev past 3500.

Waffles · Post by **Waffles** » Thu Mar 20, 2008 3:13 pm

Is your car still obd0? Pull back the passanger side floor mat and read the blinking light on the ECU.

Long = 10
Short = 1

.:si:. · Post by **.:si:.** » Thu Mar 20, 2008 3:16 pm

JurScrx;104028 wrote:Yep,just tried reseting the ecu..light stays on,on the ecu itself. Car WILL NOT rev past 3500.

sounds like a tps too me? from what ive read at least goes into a safety mode..

Spork · Post by **Spork** » Thu Mar 20, 2008 3:39 pm

btlfedgolf;104029 wrote:Is your car still obd0? Pull back the passanger side floor mat and read the blinking light on the ECU.

Long = 10
Short = 1

JurScrx;104028 wrote:Yep,just tried reseting the ecu..light stays on,on the ecu itself. Car WILL NOT rev past 3500.

he knows how to check the ecu for codes, we have been going over that in PM's for like a week. plus, he said that the light on the ecu itself is staying on... which I hope doesn't mean that the ecu is done.

can you do me a favor tho and try connecting the MAP to the other port on the throttle body? might not help, but I am more used to seeing it run to that middle port. also, try running the car and unplugging the connector to the map to see if it makes a difference in how it runs.