Official Post Your Suspension Setup Thread!

Midori · Post by **Midori** » Tue Dec 11, 2007 7:10 am

Function & Form Type II full coilovers
Skunk2 lca's
Skunk2 pro series front camber kit
Skunk2 rear camber kit
ASR rear lower subframe brace
ITR 22mm rear sway bar
Function7 solid rear sway bar bushings
Blox adj. end links
EX front lca's
ST 25.4mm front sway bar
NR>G 4 point front lower tie bar
Benen Tripod front strut bar
TDM X-Bar
Gram Lights 57 Optimise ceramic white 15x6.5 +38
Toyo Proxes T1R 205/50/15
Still to install:
Integra trailing arms with rear disks/stainless brake lines/Mugen TA bushings

typer1112 · Post by **typer1112** » Tue Dec 11, 2007 2:21 pm

Stock Type R everything with:

JIC Magic FLT-A2 coilovers

I've got a finger width between fender and tire all the way around, wish it was a little lower, but my driveway sucks

xslickwhitetegx · Post by **xslickwhitetegx** » Wed Dec 12, 2007 3:59 am

Spork;83880 wrote:you have the best combo you can buy, but you are thinking about downgrading to the skunks? :smashfreakB::smashfreakB::smashfreakB:
at some point you should be cut-off from having your suspension changed

not to mention, we all told you to buy Skunk2 coilovers instead of the GC's for what you wanted, so I will laugh my ass off if you have it all changed again.

who cares, I like the ride, but if the skunk2 ride better than ill just get them... theres always a need for improvement..no big deal, I got the cash, not your $ spending one the suspension.

Plus I know I can sell the GC and Koni for a good price

Midori · Post by **Midori** » Wed Dec 12, 2007 6:22 am

xslickwhitetegx;83874 wrote: Koni yellows w/ GC (le ones) and Koni top hats.. might swap them out if I like Alex's new Skunk2 Pro C coilovers better..

Allex has Skunk2 pro-S, not pro-C.

g3integragsr · Post by **g3integragsr** » Wed Dec 12, 2007 6:44 am

Tokico Illumina 5-Way Adjustable Shocks
Eibach Pro-Kit

Everything else is stock

Notice how the Pro-Kit sags in the rears......supposedly common on Integra's.

I only have one 12inch sub in the back so I don't think it creates that much sag

N2HIFI · Post by **N2HIFI** » Wed Dec 12, 2007 8:38 am

current:
Kyb Agx 4 way adj (4 front 3 rear )
GC coil overs
Block Rear LCA's
Skunk2 Front adjustable UCA
GSR rear sway bar
APC Front Strut tower bar

Upgrading to :
ST front swap bar
GSR Lower control arms with ES inserts (have just need to install)
NRG 4 point lower tie bar
GSR front sub frame brace
ASR rear subframe brace
Type R rear sway bar
Bloxs ADJ end links
Beaks lower tie bar
Rear disc brake conversion
Nrg or carbing 3 point front Strut Tower bar
Rear Strut tower bar
C-pillar bar
6 point roll cage

chris

Silver Knight · Post by **Silver Knight** » Wed Dec 12, 2007 11:24 pm

Skunk 2 Pro-S full adjustable coilvers. can still lower the car 3-4 inches all around.
Type-R front tower bar
soonn to have Type-R rear tower bar

Waffles · Post by **Waffles** » Wed Dec 12, 2007 11:33 pm

Eclipse: Stock as a rock

RX7: H&R springs tokico blues in the front and tokico illuminas in the back.

bildo16 · Post by **bildo16** » Thu Dec 13, 2007 2:48 am

EP3 Has:

Function and Form Type 1 Coilovers (Currently set to not so stiff, but not too soft)
Eibach Camber kit out back
BillZ Custom Alignment=Not much toe, 1 Degree Negative Camber up front, 3.4 Degrees positive caster, and 1/2 degree negative out back
Weds Sport SA-90's Bronze with some falken tires.
On the way:

Progress Rear Sway Bar
Cusco F&R Strut Tower Bars

First day home, 4 months ago

After coilovers, before wheels

With wheels (thinking of getting some t1r inverted tie rod ends so i can go a bit lower, waiting for ctr lip to justify it)

Midori · Post by **Midori** » Thu Dec 13, 2007 6:28 am

Bills car is hot.