93 EG H22 Swap info

Fzn14 · Post by **Fzn14** » Mon Jun 21, 2010 3:34 am

Ok now before someone says use the search button i have looked and looked and looked and maybe i not looking into the right place. Anyways

1.) what header can i use so i can mate up to EG Cat back system?

2.) i have a CX model..and the wiring seems to be a bit confusing as well...anyone have any straight info from a site?

i think thats its for the time being. thank you:wav:

JustRob · Post by **JustRob** » Mon Jun 21, 2010 3:51 am

Fzn14;236702 wrote:Ok now before someone says use the search button i have looked and looked and looked and maybe i not looking into the right place. Anyways

1.) what header can i use so i can mate up to EG Cat back system?

2.) i have a CX model..and the wiring seems to be a bit confusing as well...anyone have any straight info from a site?

i think thats its for the time being. thank you:wav:

You fail at searching. I found this in 2 minutes.

Header...

http://www.explicitspeedperformance.net/ESPHeader.html

CX Specific Wiring...

http://www.ff-squad.com/technet/wiring.obd1.htm

Fzn14 · Post by **Fzn14** » Mon Jun 21, 2010 11:53 am

that may be so. but i have looked at many headers and i am trying to find one that doenst have the extrension peice. it just bolts directly up. is that possiable?

JustRob · Post by **JustRob** » Mon Jun 21, 2010 2:42 pm

Fzn14;236725 wrote:that may be so. but i have looked at many headers and i am trying to find one that doenst have the extrension peice. it just bolts directly up. is that possiable?

Why don't you call them.

Gunmetal Si · Post by **Gunmetal Si** » Mon Jun 21, 2010 2:48 pm

everyone is so fucking lazy.

Fzn14 · Post by **Fzn14** » Wed Jun 23, 2010 1:23 am

ok well thank you for the info that you have gave me...However i have the 93 CX version which was not pre-wired for the vtec setup what so ever. So does this mean if i wanna keep my cabin harness the same that i will have to pin up those postions and run them into the bay or swap the whole harness?

JustRob · Post by **JustRob** » Wed Jun 23, 2010 2:03 am

Fzn14;236951 wrote:ok well thank you for the info that you have gave me...However i have the 93 CX version which was not pre-wired for the vtec setup what so ever. So does this mean if i wanna keep my cabin harness the same that i will have to pin up those postions and run them into the bay or swap the whole harness?

You run wires from the ECU pin-outs listed above for VTEC to the appropriate sensors.

Fzn14 · Post by **Fzn14** » Wed Jun 23, 2010 2:56 am

Ok that makes more sense then doing the whole harness but i just wanted to double check. The peices to actually pin the harness...where can i get those? radio shack?

JustRob · Post by **JustRob** » Wed Jun 23, 2010 3:11 am

Fzn14;236964 wrote:Ok that makes more sense then doing the whole harness but i just wanted to double check. The peices to actually pin the harness...where can i get those? radio shack?

Junkyard. Here is how it's done.

Fzn14 · Post by **Fzn14** » Wed Jun 23, 2010 3:19 am

Ya i had seen that. well hey thanks for the information