My 91 HB semi-build

dc2whore · Post by **dc2whore** » Tue May 11, 2010 12:02 am

You should get in that start it and drive it off a fucking bridge..... I kid i kid looks better then half the board already..

GAWear · Post by **GAWear** » Tue May 11, 2010 3:05 pm

90HtchBk;232068 wrote:What he said.

Well I have already started so I am going to finish them and see how they turn out. I have done all the other ones like this yes it looses texture but it looks smooth so we will see.

jpciii;232074 wrote:Are your scraping sounds coming from your front mud flaps? No sweat. They'll wear down.

No the actual bottom scraps......like I said half my drive way is concrete the other is gravel. When I come off the concrete onto the gravel which is all the same level basically there is a line of gravel moved from the scrapping.

dc2whore;232076 wrote:You should get in that start it and drive it off a fucking bridge..... I kid i kid looks better then half the board already..

lol thanks

Andrew · Post by **Andrew** » Tue May 11, 2010 6:48 pm

GAWear;232152 wrote: No the actual bottom scraps......like I said half my drive way is concrete the other is gravel. When I come off the concrete onto the gravel which is all the same level basically there is a line of gravel moved from the scrapping

id hope this "line" is pretty tall, im way lower than you and NEVER scrap the bottom of my car.

GAWear · Post by **GAWear** » Tue May 11, 2010 7:02 pm

92egdxhatch;232188 wrote:id hope this "line" is pretty tall, im way lower than you and NEVER scrap the bottom of my car.

Seriously?

I looked the other day and I will snap a picture tonight there is not much clearence at all in the front. It's ridiculous I bottom coming out of the drive way which is a like 2 inch drop from driveway to road.

Only thing I can think is possibly because the rear springs aren't in. But I thought someone said in earlier post that wouldn't affect the way it sits. IDK?

Like I said I will snap pics of it all in a few hours and post up tomorrow

Edison Carasio · Post by **Edison Carasio** » Tue May 11, 2010 8:43 pm

Not really related to the discussion at the moment, but every time I see the thread title on this it looks like "91 HB hemi-build".

GAWear · Post by **GAWear** » Tue May 11, 2010 8:47 pm

haha that would be interesting

JustRob · Post by **JustRob** » Wed May 12, 2010 5:18 am

This thread makes no sense. Good luck with whatever it is that you're trying to do.

GAWear · Post by **GAWear** » Wed May 12, 2010 5:16 pm

It is a build thread just like all others. I may not be doing a complete motor swap but plan on over time doing more to make it look better inside and out.

Anyways here is a picture of the ride hieght like I said I would get.

Height on the passenger side from ground to frame is 3 1/2 inches on the driver side there is a plastic piece that is scrapping everything underneath. It's about 3 inches or a little less from the ground.

Capt'n Obvious · Post by **Capt'n Obvious** » Thu May 13, 2010 12:31 am

Big Black;231741 wrote:yank out engine/tranny. put something more powerful in. its a honda. you have lots of possibilities. b, f, g, h, k, etc. the list goes on.

hmm never heard of the g motor do you mean j?

Phate · Post by **Phate** » Thu May 13, 2010 3:31 am

Capt'n Obvious;232374 wrote:hmm never heard of the g motor do you mean j?

A "g" is a mix of h and f motors.